Harry Potter

Crash test dummies are very important in vehicle safety. Without them the death rate in car accidents would be higher. Dummies are used so human lives can be saved. Crash test dummies have been greatly developed over the years, they are put through many tests and these tests need to be done to help improve automobiles. First of all, the development of today’s crash test dummies has required a lot of work. In 1949, the Sierra Sam was first made. It was a 95th percentile adult male dummy. It was used by the United States Air Force to test aircraft ejection seats. It had a humanlike exterior shape, body weight and some limb joints. The spine and neck designs had very little resemblance to humans. Mark I, created in 1952, was also a 95th percentile male. It was used by the U.S. and European Air Forces. This new design was similar to humans only in shape, size and total weight. The elbows, wrists, knees and ankles were one piece limbs which caused them to be too stiff to provide accurate data. As a result, only a few models were produced. Other dummy models, the F,B & P general purpose dummies, were produced in 1953 and was available in eight different sizes. It had a better design than previous models, and it provided better responses. This dummy was used for many purposes. It was used in the project Apollo Landing Testing, underwater escape tests, tractor-safety programs and many other automotive and aircraft programs. The use of this dummy was discontinued in the late 1960s. The Gard Dummy was developed in the 1960s and eight different sizes were made. It was used in testing aircraft ejection seats and in Navy programs. This design is still used in some tests today. The development of the VIP (Very Important People) model dummy started in 1966. Until this time, crash dummies were made to meet the standards of aircrafts. Previous dummies did not meet the needs for automobile testing. For example the dummies didn’t have a pelvic structure and the spine was not humanlike. The VIP model dummy was made to be more like a human and to provide more accurate and helpful information in automotive testing. The very first standard automotive crash test dummies were the VIP-50A. It was completed and shipped in early 1968. Research in making the Sierra Stan, another dummy produced to meet the needs of the automotive industry, started in 1967. It was an adult, 50th percentile male dummy. In making changes to the VIP-50A, the VIP95 and the VIPF5 model dummies were made in 1970. The VIP95 model is a large adult male dummy and the VIPF5 is a small female dummy. These two models are still used by some auto manufactures to test seat belts. Also in 1970, other Sierra models were created. Sierra Susie was an adult 5th percentile female dummy, weighting 104 pounds and was 30.9 inches high when seated. This dummy had the most humanlike appearance to that date, she wore a realistic wig. Sierra Sammy, a six year old, and Sierra Toddler, a three year old, were made. In appearance they looked correct, but neither model was built to the right weight distribution. This threw off the accuracy of test results. Another attempt at child dummies was made in 1971. The VIP3C and the VIP6C, a 50th percentile three year old and a 50th percentile six year old, were developed. The immaturity of a child’s skeleton was taken into consideration when making these two models. The spine was made of rubber column constructions. Because the dummies weren’t very humanlike, their use was limited. But it was the first good attempt in making child test dummies. Many new developments were made in 1972 regarding test dummies. The Hybrid II, a 50th percentile adult male was made to help test seat belts in cars. This model had a humanlike exterior shape, body weight and some realistic joint movements. Some main features in this model included it’s good repeatability, durability and serviceability. The Supermorophic Dummy, when created, was the most realistic model to that date. Full movement of the limbs, torso, neck and head allowed the dummy to be placed in any position. Dynamic Dan was created and used for testing ejection seats, vibration tests, parachute opening shock tests and other tests involving aircrafts. The OPAT dummy was created and was very helpful in collecting information about seat belts because of its humanlike clavicle and floating scapula and a rib cage that is very similar to a human’s. This dummy is still commercially available. In 1973 Repeatable Pete was developed. It was designed to provide accurate data from frontal impacts and lateral impacts. Because of the lack of repeatability and reproducibility, this model was never commercially available. The Hybrid III, 50th percentile male, weighs 172.3 pounds was made in 1973. It was made to improve the impact response of the test dummy to be more like a human. This dummy has a variety of optional equipment available. Because of this it is one of the most versatile test dummies